Review of El Thunder 20700

Review of El Thunder 20700

In this review, I will tell you about the mechanical mod for the 20700 battery — El Thunder 20700.

At the beginning of 2017, a new format of 20700/21700 batteries suddenly burst into the lives of vapers (as if the zoo of already existing 18340/18350/14500/16850/18500/18650/26650 was not enough). Leading and well-known manufacturers began to hesitantly announce boards and even mechanical mods. And at the end of 2017, the guys from ViVA la Cloud and El Thunder presented the first mechanical mod for this still rare battery. Structurally, it turned out to be very similar to the previous version, but with its own features, advantages and disadvantages.

Packaging and equipment

The manufacturer El Thunder remains true to its beginnings and continues to supply products in the packaging familiar to itself and its customers. It’s the same veneer tube with a leather tie, the El Thunder inscription on the side and a poorly visible seal with the model and color marking on the end. best vape kit canada The 18+ sign hasn’t gone anywhere either, although I don’t think it will scare anyone off or make them refuse to buy it at the very last moment, just imagine the mental dialogue of someone’s grandmother: “Oh no, it says 18+ right there, I can’t give this incomprehensible thing to my grandson for his 15th birthday, I’ll knit him a better cover for a husky scooter.”

Inside the mod itself, the happy buyer will later find instructions and three plastic spacers.

Appearance and characteristics

Length 87 mm

Diameter 26 mm (painted slightly thicker)

Diameter of the evaporator seat 24 mm

Mod material Brass L63

Button / pin material Brass L63

Contact group Spacer with galvanic silver

Battery format 18650/20700. Attention! 21700 is not suitable

El Thunder 20700 mech mod – instructions

The warnings say that the mod should not be given to inexperienced vapers, do not use batteries with damaged insulation, install the battery with the positive contact to the ventilation hole in the button, do not use caustic substances to clean mods with paint and be sure to contact the seller or manufacturer in case of damage to the contact group.

El Thunder 20700 mech mod – appearance

The appearance of the El Thunder mech mod is again slightly different from the classic “pipe”. Due to the increased internal hole, the external groove has become less deep, but wider, and also acquired three protruding stripes. This design allows you to confidently hold the mod even in the sweatiest palms. Between the stripes are located both the name of the device and its serial number. There are not as many color options as we would like: black, pure brass, white and the most expensive “in camouflage”. Naturally, without paint will be the cheapest, and military, on the contrary, the most expensive.

The paintwork does not cause any complaints, dense, rough and very durable. A decent thickness (about 0.15 millimeters) inspires respect and hope that the mod will not change its appearance for a very, very long time. The upper edge of the mod has additionally acquired a groove around the hole of the hybrid connector, and the contact pad itself is made with chamfers along the outer edge (which just gives a platform for the ideal fit of 24 mm diameter evaporators.

A mod simply lying on the table (especially with a battery, but without an evaporator) maximally resembles a light dumbbell for fitness and can be used for these purposes.

In one movement and in a couple of seconds, the mod can be disassembled into three parts: a cover, a button with a spring and a spacer, and a pipe.

The button consists of three parts: the brass button itself with a gas outlet hole, a steel spring, and a plastic spacer with a silver-plated washer in the center. The button and spacer are held quite tenaciously on the spring and will not fall apart into components when disassembling the device. However, you should not lose your vigilance completely, this design is not fixed in any way inside the cover and can fall out of it after unscrewing (especially if a glass spacer is used for 18650 battery).

Summary and conclusions.

What I liked:

Hybrid connector

High-quality and tenacious paint

Quality of manufacture

Nice button without distortions in operation

Constant contact

Threads and spring are not involved in the circuit

The presence of an additional spacer for drippers with a long positive pin.

Support for 18650/20700

What is simply good:

There is a hole for gas outlet and a battery protection rim under the hybrid connector

Brief instructions with important warnings and a diagram

No button lock

Grooving around the 510 connector

Similar Posts

  • Review of Advken Ayana Kit. First Look

    This article will discuss a new set of a box mod and a dripper called Ayana Kit from Advken. Most Chinese manufacturers produce their box mods complete with simple maintenance-free tanks, which at best are never removed from the boxes by experienced users, and most often the mods are bought separately. However, not all companies…

  • Review of GTS Tank by Ecigator – Not a bad start

    Ecigator is a very young player on the e-cigarette market and their product range so far includes only vaping e-cigs and mechanical boxmod. But now it’s time to expand and they have released their first tank – GTS Tank and it doesn’t look too bad. GTS Tank by Ecigator The peculiarity of the device is…

  • Review of Advken Lynx 2500

    Chinese company Advken has taken up the production of disposables, and today we will tell you about perhaps the most interesting version of the brand’s range – Lynx 2500. Advken, a well-known developer of vaping devices, has recently been producing disposable devices under the name Lynx. This range has several versions depending on the preferred…

  • Review of Joyetech eGo Pod AST Version Kit

    For many vapers who started vaping five or six years ago, the current situation on the vaping market is a little bit unclear how it happened that” vapers, from which many started, have been revived again, but in a slightly modified version of POD-systems. The popularity and demand for POD-systems is explained quite simply after…

  • Review of Меchmod Constanta by FIR

    Today I want to tell you about one of the very first samples of the new product that I got my hands on for testing. Meet Constanta by FIR. Packaging and accessories of the Constanta mech mod The Constanta mech mod comes in a tin tube decorated all over with the Planck-Dirac constant symbol (if…

  • Review of Geekvape Aegis X Kit. First look

    The reason for this article was the long-awaited new product from Geekvape in the form of a continuation of the line of protected box mods Aegis. The series of box mods under the general name Aegis is considered one of the most successful products of the Chinese manufacturer of devices Geekvape. Indeed, these devices are…